Klipper probe config for the BIQU Microprobe (V1/V2)

biqu_microprobe.cfg

## --- BIQU Microprobe Klipper configuration ---
# Not much different from a standard probe config. The
# main difference compared to most probes is to disable
# deactivating the probe (PROBE_UP) after each sample
#
# You can either copy pasta this directly or import
# into your config.yml using [include microprobe.cfg]
#
# Note: if you are changing from a bltouch or one of its
# clones, remove/comment out the [bltouch] config!
# That also includes any auto generated config stored
# at the bottom by the PROBE_CALIBRATE command
#
# Note: the current control and sensor pin values are
# configured for the 'BTT SKR E3 mini V2' controller 
# board. You may need to update these values depending
# on your controller board model.
#
# Update (2023-10-17): This config is configured for
# the V1 microprobe. V2 users must update the 
# polarity of the sensor pin in the config to be 
# pull-down (^!) not pull up (^)

[gcode_macro PROBE_DOWN]
gcode:
    SET_PIN PIN=probe_enable VALUE=1

[gcode_macro PROBE_UP]
gcode:
    SET_PIN PIN=probe_enable VALUE=0

[output_pin probe_enable]
pin: PA1  # Set to the control pin on your board
value: 0

[probe]
pin: ^PC14  # NOTE FOR V2 users: Set this to ^!PC14 to set the low level trigger 
deactivate_on_each_sample: False
x_offset: -40
y_offset: -35
z_offset: 0  # Will be overridden when you do a PROBE_CALIBRATE
samples: 2
samples_tolerance: 0.05
samples_tolerance_retries: 3
activate_gcode:
    PROBE_DOWN
    G4 P500
deactivate_gcode:
    PROBE_UP

I have a M8P V1.1 board and some trouble with this microprobe (maybe V2). Trying the BLTouch installation has no success and after a while i am landing here. It was a big step in the right direction. But i had always „still triggered“ errors. One of my tries with „!“ and the „^“ was to remove the pull up from PC14 - and it works now without an error - better to write PB2 -

The correct command is instead of PC14 !PB2 for the manta m8p without pull up.

After doing a manual test again - i failed. So i tested again and again. Every time i have „still triggered after rectract“. My fault was to simulate the nearing heatbed i took something flat to trigger the microprobe. I forgot that the stepper makes a small movement back and forward after - and I relay don‘t how sensitiv this probe is. I tested again with a little touch and a second after a very short time and my test was successful.

Ok in summery .. instead of ^PC14 the very very correct command is: pin: ^!PB2 for the Manta M8P

Thank you for this thread - it was a great help for me :)

Ok in summery .. instead of ^PC14 the very very correct command is: pin: ^!PB2 for the Manta M8P

Thank you for this thread - it was a great help for me :)

No worries! Glad you got it all sorted. I'll revise the config to include a note about different controller boards. ^PC14 works for my BTT SKR Mini E3 V2 (and probably a bunch of other BTT boards), but in a lot of cases this value will be different.

J'ai une carte M8P V1.1 et quelques soucis avec cette microsonde (peut-être V2). Essayer l’installation de BLTouch n’a pas réussi et après un moment j’atterris ici. C'était un grand pas dans la bonne direction. Mais j'avais toujours "encore déclenché" des erreurs. Un de mes essais avec "!" et le "^" était de supprimer le pull up du PC14 - et cela fonctionne maintenant sans erreur - mieux vaut écrire PB2 -

La commande correcte est au lieu de PC14 !PB2 pour le manta m8p sans pull up.

Après avoir refait un test manuel, j'ai échoué. J'ai donc testé encore et encore. À chaque fois, j'ai "toujours déclenché après rétractation". Ma faute était de simuler l'approche du lit chauffant, j'ai pris quelque chose de plat pour déclencher la microsonde. J'ai oublié que le stepper fait un petit mouvement d'avant en arrière après - et je ne sais pas à quel point cette sonde est sensible. J'ai testé à nouveau avec une petite touche et une seconde après un temps très court et mon test a été réussi.

Ok en résumé .. au lieu de ^PC14 la commande très très correcte est : pin: ^!PB2 pour le Manta M8P

Merci pour ce fil, il m'a été d'une grande aide :)

Good morning !
I come to you because I am desperate to find a solution to my problem!
I am new to klipper and I use a BTT mp8 card with a V2 microprobe as well, but at the moment I cannot trigger this probe, I had the same problem as you, but being on ratos ( klipper) I'm at a dead end, can you provide your configuration lines for this pin please? I'm really in a big problem
friendly

@cylon1975 I found the manual for V2 probe :) . It has a section for the Manta 8P. The configuration is quite different depending on whether you have the M8P v1.1 or the M8P v2.0.

https://github.com/bigtreetech/MicroProbe/blob/master/MicroProbe%20V2%20User%20Manual_20240304.pdf

^!PB2 Is what you want for your sensor pin (pull down configuration since you are using a Microprobe V2)
PB1 Is you control pin

@cylon1975J'ai trouvé le manuel de la sonde V2 :) . Il dispose d'une section pour le Manta 8P. La configuration est assez différente selon que vous possédez le M8P v1.1 ou le M8P v2.0.

https://github.com/bigtreetech/MicroProbe/blob/master/MicroProbe%20V2%20User%20Manual_20240304.pdf

^!PB2Est-ce que vous voulez pour la broche de votre capteur (configuration déroulante puisque vous utilisez une Microprobe V2) PB1Est-ce que vous contrôlez la broche

Hello and thank you for your quick response !! I finally succeeded by copying the script list by creating a fileMicroProbe.cfgand report this file inprinter.cfg!! Thanks again for the help !!                                                                                                                                                                 

@PaulStep61 You need to tab all the gcodes that you call.

gcode:
SET_PIN PIN=probe_enable VALUE=1

This does not work, it should rather be:

gcode:
    SET_PIN PIN=probe_enable VALUE=1

Otherwise klipper will see it as its own variable inside the config, rather than the gcode belonging to a variable.

Important note for V2 users, especially those coming from the world of Marlin. The BTT SK3 Mini E3 V3 + Marlin usually requires the use of the Z_STOP connector on the board to be connected to the probe (thus removing the need for the physical Z endstop). However, this means that the probe pin would need to be set to ^!PC2 (and not ^!PC14) for the probe not to smash on the printbed.
In brief, here are the important parts of the configuration file:

[stepper_z]
step_pin: PB0
dir_pin: PC5
enable_pin: !PB1
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_min: -2
#position_endstop: 0
position_max: 250

#...

# required for any probe, bltouch...Adjust the X,Y values to your printer. I use an Ender3-pro
[safe_z_home]
home_xy_position: 135,135
z_hop: 5

[gcode_macro PROBE_DOWN]
gcode:
    SET_PIN PIN=probe_enable VALUE=1

[gcode_macro PROBE_UP]
gcode:
    SET_PIN PIN=probe_enable VALUE=0

[output_pin probe_enable]
pin: PA1  # Set to the control pin on your board
value: 0

[probe]
pin: ^!PC2
deactivate_on_each_sample: False
#adjust offsets to fit your configuration
x_offset: 38
y_offset: -29.5
z_offset: 0
samples: 2
samples_tolerance: 0.05
samples_tolerance_retries: 3
activate_gcode:
    PROBE_DOWN
    G4 P500
deactivate_gcode:
    PROBE_UP