fflsliver default config

default.cfg

# ffslicer default is config file

precision = 0.1                 # valid range [0.01, 0.4], default is 0.1
filamentDiameter = 1.75         # valid range [0.5, 10.0], default is 1.75
extrusionRatio = 1.09           # valid range [0.5, 2.0], default is 1.0
layerHeight = 0.18              # valid range [0.01, 0.4], default is 0.18
firstLayerHeight = 0.27         # valid range [0.05, 0.5], default is 0.27
pathWidth = 0.4                 # valid range [0.35, 0.45], default is 0.4
baseSpeed = 80                  # valid range [10, 200], default is 80
travelSpeed = 120               # valid range [10, 200], default is 120
minSpeed = 5                    # valid range [1, 20], default is 5
rightTemp = 200                 # valid range [0, 260], default is 200
leftTemp = 200                  # valid range [0, 260], default is 200
platTemp = 50                   # valid range [0, 120], default is 50
vaseMode = false                # valid value is {true, false}, default is false
lineNumber = false              # valid value is {true, false}, default is false
stopPos = homing                # valid valule is {center, homing}, deafult is homing

[dimension]
enable = false                  # valid range {true, false}, default is false
innerOfs = 0.1                  # valid range [-10.0, 10.0], default is 0.1
outerOfs = 0.0                  # valid range [-10.0, 10.0], default is 0.0

[shell]
count = 2                       # valid range [0, 10], default is 2
outerMaxSpeed = 40              # valid range [10, 200], default is 40
outerSpeedRatio = 0.5           # valid range [0.1, 1.0], default is 0.5
visibleInnerSpeedRatio = 0.7    # valid range [0.1, 1.0], default is 0.7
invisibleInnerSpeedRatio = 1.0  # valid range [0.1, 1.0], default is 1.0
innerOverlapRatio = 0.3         # valid range [0.0, 0.5], default is 0.3
maxThinwallRatio = 1.3          # valid range [1.1, 1.9], default is 1.3
minThinwallRatio = 0.4          # valid range [0.2, 0.8], default is 0.4
seamSpeedRatio = 0.15           # valid range [0.05, 0.3], default is 0.15
decelerateDist = 10.0           # valid range [0.0, 20.0], default is 10.0
randStart = false               # valid value is {true, false}, default is false
startClosestX = -10000.0        # valid range [-10000.0, 10000.0], default is -10000.0
startClosestY = -100.0          # valid range [-10000.0, 10000.0], default is 0.0
alterableStart = true           # valid range {true, false}, default is true

[infill]
topSolidCnt = 3                 # valid range [1, 30], default is 3
bottomSolidCnt = 3              # valid range [1, 30], default is 3
density = 0.15                  # valid range [0.0, 1.0], default is 0.15
shape = hexagon                 # valid valule is {line, triangle, hexagon}, deafult is hexagon
overlapRatio = 0.15             # valid range (-0.7, 0.7), default is 0.15
startAngle = 45                 # valid range [0, 180], default is 45
crossAngle = 90                 # valid range [0, 180], default is 90
topMaxSpeed = 70                # valid range [10, 200], default is 70
solidSpeedRatio = 0.7           # valid range [0.1, 1.0], default is 0.7
sparseSpeedRatio = 1.0          # valid range [0.1, 1.0], default is 1.0
solidCombineCnt = 1             # valid range [1, 4], default is 1
sparseCombineCnt = 2            # valid range [1, 4], default is 2
minCombineLayerArea = 150       # valid range [0, 10000], default is 150
insideSolidInterval = 0         # valid range [0, 9999], default is 0
insideSolidCnt = 1              # valid range [1, 30], default is 1

[bridge]
enable = true                   # valid range {true, false}, default is true
minArea = 15                    # valid range [5, 500], default is 15
speedRatio = 0.8                # valid range [0.5, 1.0], default is 0.8
angleResolution = 15            # valid range [5, 30], default is 15

[raft]
enable = false                  # valid range {true, false}, default is false
extruderId = 0                  # valid range {0, 1}, default is 0
margin = 5.0                    # valid range [3.0, 10.0], default is 5.0
liftHeight = 0.2                # valid range [0.0, 0.4], default is 0.2
aboveExtrusionRatio = 0.6       # valid range [0.1, 1.0], default is 0.6
bottomHeight = 0.4              # valid range [0.2, 0.4], default is 0.4
bottomWidth = 2.0               # valid range [0.4, 4.0], default is 2.0
bottomDensity = 0.5             # valid range [0.05, 1.0], default is 0.5
bottomSpeed = 10                # valid range [5, 30], default is 10
middleHeight = 0.2              # valid range [0.1, 0.4], default is 0.2
middleWidth = 0.4               # valid range [0.1, 0.4], default is 0.4
middleDensity = 0.3             # valid range [0.05, 1.0], default is 0.3
middleLayerCnt = 1              # valid range [1, 3], default is 1
middleSpeed = 60                # valid range [20, 80], default is 60
topHeight = 0.2                 # valid range [0.1, 0.4], default is 0.2
topWidth = 0.4                  # valid range [0.1, 0.4], default is 0.4
topDensity = 0.95               # valid range [0.2, 1.0], default is 0.95
topCrossAngle = 90              # valid range [0, 180], default is 90
topLayerCnt = 2                 # valid range [1, 4], default is 2
topSpeed = 60                   # valid range [20, 120], default is 60
bottomTempAdjust = 5            # valid range [0, 20], default is 5

[preExtrude]
enable = true                   # valid range {true, false}, default is true
margin = 5.0                    # valid range [3.0, 10.0], default is 5.0
length = 120.0                  # valid range [50.0, 200.0], default is 120.0
layerHeight = 0.2               # valid range [0.1, 0.4], default is 0.2
pathWidth = 1.6                 # valid range [0.4, 2.0], default is 1.6
speed = 20                      # valid range [10, 50], default is 20

[retract]
length = 1.3                    # valid range [0.0, 50.0], default is 1.3
speed = 30                      # valid range [10, 200], default is 30

[wall]
enable = false                  # valid range {true, false}, default is false
count = 2                       # valid range [1, 5], default is 2
distance = 5.0                  # valid range [1.0, 15.0], default is 2.5
speed = 60                      # valid range [10, 200], default is 60

[brim]
enable = false                  # valid range {true, false}, default is false
extruderId = 0                  # valid range {0, 1}, default is 0
margin = 5.0                    # valid range [1.0, 10.0], default is 5.0
layerCnt = 1                    # valid range [1, 5], default is 1
speed = 60                      # valid range [10, 200], default is 60
excludeInterior = false         # valid range {true, false}, default is false

[lineSupport]
speedRatio = 1.0                # valid range [0.5, 1.0], default is 1.0
deltaXY = 0.35                  # valid range [0.05, 1.0], default is 0.35
deltaZ = 0.2                    # valid range [0.0, 0.5], default is 0.2
deltaRaft = 0.15                # valid range [0.0, 0.4], default is 0.15
areaUnionMaxDist = 4.0          # valid range [1.0, 10.0], default is 4.0
pathStep = 2.0                  # valid range [0.8, 10.0], default is 2.0
extrusionRatio = 0.6            # valid range [0.25, 1.0], default is 0.6
outlinePath = false             # valid range {true, false}, default is false
topSolidCnt = 0                 # valid range [0, 3], default is 0
separateInterface = false       # valid range {true, false}, default is false
topIntfcCnt = 3                 # valid range [1, 30], default is 3
bottomIntfcCnt = 3              # valid range [1, 30], default is 3

[treeSupport]
maxSpeed = 60                   # valid range [10, 100], default is 60
speedRatio = 0.6                # valid range [0.3, 1.0], default is 0.6
deltaXY = 0.2                   # valid range [0.05, 0.5], default is 0.2
shellCnt = 3                    # valid range [1, 4], default is 3
liftTravel = true               # valid range {true, false}, default is true
separateInterface = false       # valid range {true, false}, default is false
topIntfcCnt = 3                 # valid range [1, 30], default is 3
bottomIntfcCnt = 3              # valid range [1, 30], default is 3

[fullSupport]
enable = false                  # valid range {true, false}, default is false
extruderId = 0                  # valid range {0, 1}, default is 0
speedRatio = 1.0                # valid range [0.5, 1.0], default is 1.0
overhangAngle = 45              # valid range [15, 75], default is 45
deltaXY = 0.1                   # valid range [0.0, 0.5], default is 0.1
margin = 1.0                    # valid range [0.0, 5.0], default is 1.0
stackAngle = 30                 # valid range [15, 45], default is 30
maxStackArea = 150              # valid range [50, 500], default is 150
density = 0.15                  # valid range [0.1, 0.5], default is 0.15
topSolidCnt = 3                 # valid range [1, 6], default is 3
separateInterface = false       # valid range {true, false}, default is false
topIntfcCnt = 3                 # valid range [1, 30], default is 3
bottomIntfcCnt = 3              # valid range [1, 30], default is 3

[speed]
bottomLayerMax = 30             # valid range [10, 70], default is 30
firstLayerMax = 20              # valid range [10, 60], default is 20
firstLayerMaxTravel = 70        # valid range [10, 100], default is 70
startMax = 25                   # valid range [5, 50], default is 25
accelerateDist = 5              # valid range [0.0, 20.0], default is 5.0

[fan]
state = raftBasePrinted         # valid value is {alwaysOn, alwaysOff, raftBasePrinted, toPresetHeight, printingRaftTop}, default is raftBasePrinted
turnOnHeight = 0.0              # valid range [0.0, 300.0], default is 0.0
extraState = alwaysOn           # valid value is {alwaysOn, alwaysOff}, default is alwaysOn

[delay]
enable = true                   # valid range {true, false}, default is true
decelerateMM2 = 50              # valid range [25, 500], default is 50
delayMM2 = 25                   # valid range [0, 300], default is 25
maxDelayMsec = 3000             # valid range [1000, 6000], default is 3000

[voltage]
voltageX = 100                  #  valid range [80, 127], default is 100
voltageY = 100                  #  valid range [80, 127], default is 100
voltageZ = 40                   #  valid range [20, 100], default is 40
voltageA = 100                  #  valid range [60, 120], default is 100
voltageB = 100                  #  valid range [60, 120], default is 100

[svg]
baseTime = 3.0                  # valid range [1.0, 60.0], default is 3.0
attachLayer = 4                 # valid range [0, 10], default is 4
attachTime = 5.0                # valid range [1.0, 60.0], default is 5.0
lightIntensity = 1.0            # valid range [0.01, 2.0], default is 1.0
adjustX = 100.0                 # valid range [50.0, 150.0], default is 100.0
adjustY = 100.0                 # valid range [50.0, 150.0], default is 100.0

[svgRaft]
enable = true                   # valid range {true, false}, default is true
margin = 10.0                   # valid range [0.0, 15.0], default is 10.0
thickness = 0.2                 # valid range [0.2, 2], default is 0.2
squareOutline = true            # valid range {true, false}, default is true
bevelEdge = false               # valid range {true, false}, default is false
edgeAngle = 30                  # valid range [15, 75], default is 30
edgeHeight = 2                  # valid range [1, 5], default is 2
edgeThickness = 1               # valid range [0.5, 5], default is 1

[svgInfill]
enable = false                  # valid range {true, false}, default is false
topSolidCnt = 40                # valid range [10, 300], default is 40
bottomSolidCnt = 40             # valid range [10, 300], default is 40
shellThickness = 2.0            # valid range [1.0, 10.0], default is 2.0
infillThickness = 1.0           # valid range [0.5, 5.0], default is 1.0
density = 0.2                   # valid range [0.0, 1.0], default is 0.2
zPrecision = 0.1                # valid range [0.025, 0.25], default is 0.1

[prepOfs]
enable = false                  # valid range {true, false}, default is false
angle = 0.0                     # valid range [-15.0, 15.0], default is 0.0

[waxHexaSup]
enable = false                  # valid range {true, false}, default is true
margin = 0.0                    # valid range [0.0, 1.0], default is 0.0
topSolidThickness = 1.0         # valid range [0.1, 10.0], default is 1.0
bottomSolidThickness = 0        # valid range [0, 10.0], default is 0
shellThickness = 1.0            # valid range [0.25, 5.0], default is 1.0
infillThickness = 0.5           # valid range [0.25, 5.0], default is 1.0
density = 0.5                   # valid range [0.0, 1.0], default is 0.5
roofGradient = 60               # valid range [15, 85], default is 60
zPrecision = 0.1                # valid range [0.025, 0.25], default is 0.1

[waxPostSup]
enable = true                   # valid range {true, false}, default is false
margin = 0.0                    # valid range [0.0, 1.0], default is 0.0
topSolidThickness = 1.0         # valid range [0.1, 10.0], default is 1.0
shellThickness = 0.3            # valid range [0.0, 5.0], default is 0.3
postSize = 1.0                  # valid range [0.25, 5.0], default is 1.0
postSpace = 0.2                 # valid range [0.05, 0.5], defaut is 0.2
gapRatio = 0.3                  # valid range [0.0, 0.6], defaut is 0.3
gapAngle = 60                   # valid range [15, 75], default is 60
roofGradient = 60               # valid range [15, 85], default is 60
zPrecision = 0.1                # valid range [0.025, 0.25], default is 0.1

[waxWallClip]
enable = true                   # valid range {true, false}, default is true
fastRatio = 0.3333333           # valid range [0.0, 1.0], default is 0.333333
clipMargin = 0.1                # valid range [0.05, 0.5], default is 0.1