Simple guide for setting up OTG modes on the Raspberry Pi Zero - By Andrew Mulholland (gbaman).
The Raspberry Pi Zero (and model A and A+) support USB On The Go, given the processor is connected directly to the USB port, unlike on the B, B+ or Pi 2 B, which goes via a USB hub.
Because of this, if setup to, the Pi can act as a USB slave instead, providing virtual serial (a terminal), virtual ethernet, virtual mass storage device (pendrive) or even other virtual devices like HID, MIDI, or act as a virtual webcam!
It is important to note that, although the model A and A+ can support being a USB slave, they are missing the ID pin (is tied to ground internally) so are unable to dynamically switch between USB master/slave mode. As such, they default to USB master mode. There is no easy way to change this right now.
It is also important to note, that a USB to UART serial adapter is not needed for any of these guides, as may be documented elsewhere across the internet.
##Which process should I choose?
There are 2 routes you can take for setting up the Raspberry Pi Zero as a USB Slave (OTG mode).
- The quick route - The quick route doesn't require anything beside your Pi Zero, SD card and a Windows, Mac or Linux computer. It though only supports setting up the Pi Zero as a virtual Ethernet device (allowing full SSH, SFTP, VNC etc). For any of the other USB Gadget drivers (beside g_ether), use route 2.
- The modular slower, but more flexible route - This route requires a screen and keyboard to configure your Pi Zero once it has completed its first boot.
###1. Very quick way (No USB keyboard, mouse, HDMI monitor needed)
The newer method has now been brought out into a separate Gist, which can be found here.
###2. Modular, but slower to setup method
For this method, a Pi Zero, SD card (with Raspbian Jessie lite or full), screen and keyboard are required.
You are able to set up any of the below modules using this method and are not just limited to g_ether. The required kernels are also now shipped with Raspbian 2016-05-10 releases and beyond. So no need to do a raspi-update.
No web connectivity is required, nor is a USB-UART adapter required for this method.
This documentation is based off the initial excellent work done on this Github pull request.
Modules included
- Serial (g_serial)
- Ethernet (g_ether)
- Mass storage (g_mass_storage)
- MIDI (g_midi)
- Audio (g_audio)
- Keyboard/Mouse (g_hid)
- Mass storage and Serial (g_acm_ms)
- Ethernet and Serial (g_cdc)
- Multi (g_multi) - Allows you to configure 2 from Ethernet, Mass storage and Serial
In addition to the above modules, a few other (less useful) modules are included. - Webcam (g_webcam)
- Printer (g_printer)
- Gadget tester (g_zero)
- First, flash Jessie (only tested on full, lite version may also work though) onto a blank microSD card.
- (step only needed if running Raspbain version before 2016-05-10) Once it starts up again, run
sudo BRANCH=next rpi-update. This will take a while. - Next we need to make sure we are using the dwc2 USB driver
echo "dtoverlay=dwc2" | sudo tee -a /boot/config.txt. - And enable it in Raspbian
echo "dwc2" | sudo tee -a /etc/modules - Need to now pick which module you want to use from the list above, for example for ethernet
echo "g_ether" | sudo tee -a /etc/modules. You can only pick one of the above modules to use at a time.
- g_serial - To use the standard serial module, you need to tell the Pi to forward the serial console to it with
sudo systemctl enable [email protected], then you can connect to the device via Putty or Screen. - g_ether - Using virtual ethernet, you should simply be able to ssh into the address of your Raspberry Pi. To do this, there is a little extra configuration required though. There is a few ways we could set up the point to point networking. The proper way would be to set up a DHCP server on one of the ends. A far simplier was though is just to give the Raspberry Pi a fixed IP address. To do this, you will need to run
echo -e "interface usb0 \nstatic ip_address=169.254.64.64" | sudo tee -a /etc/dhcpcd.conf. You can then access the Raspberry Pi Zero by connecting to169.254.64.64, or by usingraspberrypi.localif your computer has Bonjour installed (Mac and most Linux OSs including Raspbian). Note this method does not support adding a fixed address to the cmdline.txt file. For that, you have to use the Ethernet only kernel below. - g_mass_storage - To have your Pi Zero appear as a mass storage device (flash drive), first create a mini filesystem in a file on your Pi with
sudo dd if=/dev/zero of=/piusb.bin bs=512 count=2880and set it up as a fat32 filesystem withsudo mkdosfs /piusb.bin. Then, when enabling it, addfile=/piusb.bin stall=0onto the end, for examplesudo modprobe g_mass_storage file=/piusb.bin stall=0.
In theory, most USB devices should work alongside these kernels, to switch to USB OTG mode, simply don't use an OTG adapter cable and use a standard USB cable to plug your Pi Zero into another computer, it should auto switch.
The legacy guides can be found on a separate Gist.
is there any way to use the route one (g_ether) and the route two which is the other g_ modules at the same time? I want to have the mass storage and the ssh on one windows without other internet connections.
I've tried .. after i finished the route 1 , when I am trying to emulate the storage device , the pc didnot have any sign after i did the modprobe command even i re-plugin , sometimes it cannot be recognized after doing that
is there a way to do this?
thanks